Tip: Let the car sit outside for a couple of hours in the sun before starting your work. Window tinting is easier to work with and the adhesive is more pliable when it is a sunny day and the temperature is at least 75 degrees. If you applied the tint yourself or it is out of warranty, decide if you want to repair it yourself or hire a professional.
#TINTED WINDOW CAR PROFESSIONAL#
Step 1: Check on the warranty: If you paid a professional to apply the tinting and it is still under warranty, call them and ask for it to be repaired or replaced entirely. Warning: There are state and city ordinances that pertain to tinting so make sure you are within the laws before applying or repairing a window tint.įollow these instructions to fix the most common issues with window tinting.It is possible to repair a bad tint job yourself, if necessary.
It can peel, or bubble, which not only looks awful but also prevents it from doing its job. Window tinting can go bad if not properly applied. In most cases, using a professional is the best option, but, unfortunately, not every professional is as skilled as he or she should be, which can lead to a sub-par tinting job that needs to be fixed. Window tinting can be a do-it-yourself project, but it requires serious attention to detail and patience. Thicknesses range from 0.001 to 0.004 inches and there are a number of different adhesives to apply the tinting to the windows. Tinting comes in a variety of thicknesses and degree of tinting.
#TINTED WINDOW CAR WINDOWS#
A transparent, very thin sheet of film is applied to the windows of a vehicle. Window tinting is a pretty simple process.
#TINTED WINDOW CAR DRIVERS#
You'll save plenty of money and have a better insulated car.Tinted windows on a car are a great way to improve its look, and they help keep both the sun and the prying eyes of other drivers and potential thieves out of your vehicle. Repeat this process for all windows until the job is complete.įor the cost of a few basic tools and materials, a DIY car tint is a worthwhile project. If any bubbles or fingers of trapped air or application solution remain in the film, use a heat gun to gently warm the area and then run the squeegee over the bubbles toward the closest edge of the window. Use the cloth to wipe down door trims and paint. The cloth will absorb any remaining application solution. Wrap the squeegee in a lint-free cloth and run it across the entire window. Use the squeegee to push all the air and water out from beneath the film. Use the squeegee to hold the window gasket out while sliding the film in underneath it. Roll up the window and spray the film again with application solution. Run the squeegee along the top of the window, pushing any air and water out of the top as you go. Move the tint into place at the top of the window, leaving a 1/8-inch gap from the top of any sliding window. Fold the bottom edge back onto itself to avoid it touching the door trim. Discard the protective liner and remove the film from the outside of the window and place it on the inside of the window.
Spay the adhesive surface of the film with application solution as you peel. Spray the inside of the window with the application solution.įix the film to the corner of the window with a piece of clear tape and start to peel the protective liner from the film. For non-sliding windows, use the window gaskets as a template and cut the film right to the edges. This will ensure coverage beyond the base of the window. Slide the film up about half an inch before cutting along the bottom of the window, using the window gasket as a template. Round the edges off using your finger as a guide. Run the squeegee over the tint to make sure it doesn't move.įor sliding windows, roll the window down from the door frame about a quarter of an inch and cut the top and sides of the film to shape, using the window as a template. The solution will hold the film in place while you cut it to size, but will allow you to maneuver the film to make a precise cut. Put the application solution on the outside of the window and roll the tint film over the window with the protective-film layer facing upward. Run the squeegee across the window from side to side, starting from the top and working down the window to remove any leftover debris and solution. Be careful not to gouge the glass with the blade. This will remove any dust, grime and debris. Run the scraper blade across the window from side to side, starting from the top and gently working your way down the window. Play icon The triangle icon that indicates to play
0 kommentar(er)
